Strutconfigurator
Data cables

Cat6A vs fibre: what goes where in the containment

Updated 5 min readBy Ismail Yeşilay · Strutconfigurator

Short answer

Use Cat6A up to 100 m and wherever devices draw power over the cable (PoE), such as access points and cameras. Use fibre for longer distances, backbones and high-density links between racks. Fibre takes far less space per link in the containment and ignores interference, though it needs protection from crushing and tight bends.

Cat6A vs fibre is usually framed as a network decision, yet it lands on the containment designer’s desk too. The choice decides how far each link can run, whether devices take power over the cable and how much basket you need. For the route itself that last point matters most: copper is thick, heavy and sensitive to interference, fibre is thin, light and fragile. Here are the differences side by side, when to use which and what each means for the containment.

How do Cat6A and fibre compare?

Feature Cat6A (copper) Fibre OM4 (multimode) Fibre OS2 (singlemode)
Typical location Desks, access points, cameras, in-rack Within the hall, between racks and rows Between halls, buildings, campus
Reach 100 m channel, 10GBASE-T [1][2] 100 m at 100GBASE-SR4 [3] 10 km at 100GBASE-LR4 [3]
Power over the cable Yes, PoE up to 90 W at the switch [4] No No
Diameter 7.5–8.0 mm 2.0 mm patch, 6.0 mm MPO-12 trunk 2.0 mm patch, 6.0 mm MPO-12 trunk
Sensitive to interference Yes No No
Connector RJ45 LC, MPO LC, MPO

Diameters: rule of thumb, indicative (typical datasheet values).

When is Cat6A the right choice?

Cat6A is the default for anything within 100 m that has a network port. Its big advantage is power over the same cable. With PoE to IEEE 802.3bt the switch delivers up to 90 W per port [4], enough for access points, cameras, access control and lighting control without a separate supply. In a data hall, Cat6A is mostly found within the rack and between neighbouring racks, for example from a top-of-rack switch to the servers. Links between rows and to the main distribution area are usually fibre.

Watch the heat with PoE. Data cables carrying power warm up, and large bundles run hotter than loose cables. ISO/IEC TS 29125 deals with this effect [5], so keep bundles small and lay them loose in open basket.

Cat6A comes as U/FTP (foil around each pair) and S/FTP (foil around each pair plus an overall braid). S/FTP is slightly larger and heavier, and the better choice on routes shared with a lot of power cabling.

When is fibre the right choice?

Choose fibre for distance, bandwidth and density:

  • Distance. Anything over 100 m, such as links between halls, floors and buildings. OS2 reaches 10 km at 100GBASE-LR4 [3].
  • Backbone and data hall. Between racks and the main distribution area. OM4 carries 100 Gbit/s over 100 m [3].
  • Density. MPO trunks put many links into one slim cable. See MPO/MTP trunk cables.
  • Interference. Fibre is immune to electromagnetic fields, so it can run close to power.

OM4 or OS2? Choose OM4 for short links within the hall, where multimode optics are enough. Choose OS2 for runs over 100 m, between buildings, or where the fibre has to outlast several generations of equipment. If in doubt on a backbone, run both in the same basket: an extra trunk takes very little room.

How much containment space does each need?

For the support system, this is the biggest difference. A worked example for 72 links:

Option Cables Area per cable Total
Cat6A U/FTP, 7.5 mm 72 44.2 mm² 3,181 mm²
MPO-12 trunk, 6.0 mm (6 duplex links per trunk) 12 28.3 mm² 339 mm²

Calculated with π/4 × d²; diameters rule of thumb, indicative.

At 40% fill the copper needs about 8,000 mm² of containment, for example a 150×55 mm basket. The fibre fits in a 100×30 mm basket with room to spare. Weight differs as much: 72 Cat6A cables weigh about 4.3 kg per metre (rule of thumb, indicative), twelve trunks a fraction of that. The method is in cable tray fill calculation.

What does each mean for the containment?

Point Cat6A Fibre
Segregation from power Yes, to BS EN 50174-2 and BS 7671 528.1 [6][7] Only mechanical, against crushing
Bend radius 4 to 8 × d 10 × d unloaded, 20 × d while pulling
Weight Drives support centres Low
Drop into the rack Waterfall with a generous radius Waterfall, no sharp edges
Bundling Small bundles, hook-and-loop ties Hook-and-loop ties, never pulled tight

Bend radius: rule of thumb, indicative. The cable datasheet governs.

Never secure fibre with tightly pulled cable ties. They squeeze the cable and increase attenuation. Use hook-and-loop ties. More on separation in power and data cable segregation.

What mistakes come up most with copper and fibre?

The same mistakes appear on site again and again. Most of them are avoidable at the design stage:

  • Fibre at the bottom of a copper basket. Every extension adds copper on top. A few years later the fibre sits under the weight of hundreds of cables.
  • Cable ties pulled tight on fibre. The tie squeezes the jacket and attenuation rises. Use hook-and-loop ties.
  • Tight drops into the rack. A kink over the basket edge harms copper and fibre alike. Plan a waterfall at every rack.
  • PoE in one big bundle. Cables carrying power warm up. Spread them over smaller bundles in open basket.
  • Copper beyond 100 m. A Cat6A channel stops at 100 m [1]. If a rack sits further from the comms room, plan fibre or an extra distributor.
  • No room to grow. Keep fill at 40% at handover (rule of thumb, indicative) so cables can be added later.

How do you combine both on one route?

Most projects need both. A practical build-up above a row of racks:

  1. Fibre in its own narrow basket, so it never ends up under the copper.
  2. Cat6A in a wider basket alongside or above, with room to grow.
  3. Power on a separate tier, at a distance from the copper.

In the configurator you add cables per tray, copper and fibre mixed or separated. It shows the fill per tray and flags power and data sharing a tray without a divider. The cables can then be made to length, see custom length data cables.

Where do these figures come from?

  1. ISO/IEC 11801-1, Information technology. Generic cabling for customer premises. Part 1: General requirements (Class EA, 100 m channel).
  2. IEEE 802.3an, 10GBASE-T over balanced copper cabling.
  3. IEEE 802.3bm (100GBASE-SR4 over multimode) and IEEE 802.3ba (100GBASE-LR4 over singlemode).
  4. IEEE 802.3bt, Power over Ethernet up to 90 W at the power sourcing equipment (Type 4).
  5. ISO/IEC TS 29125, Telecommunications cabling requirements for remote powering of terminal equipment.
  6. BS EN 50174-2, Information technology. Cabling installation. Installation planning and practices inside buildings.
  7. BS 7671, Requirements for Electrical Installations (IET Wiring Regulations), regulation 528.1.
  8. Cable diameters, weights and bend radii: typical datasheet values (rule of thumb, indicative). The datasheet of the chosen cable governs.

Frequently asked questions

How far can Cat6A run?

A Cat6A channel is limited to 100 m: 90 m of fixed cabling plus 10 m of cords (ISO/IEC 11801-1). Over that distance 10GBASE-T delivers 10 Gbit/s. Beyond 100 m, use fibre.

Can fibre share a cable basket with copper?

Yes. Fibre is immune to electromagnetic interference. The concern is weight: copper bundles and power cables can crush it. In data centres fibre usually gets its own basket, tier or dedicated raceway.

How much space does fibre save in the containment?

A 6 mm MPO-12 trunk takes 28.3 mm² and carries 12 fibres, enough for 6 duplex links. Six 7.5 mm Cat6A cables take 265 mm² together. Per link that is more than nine times less space (diameters indicative).

What is the minimum bend radius for fibre cable?

As a rule of thumb 10 times the cable diameter with no load and 20 times while pulling (indicative). For Cat6A it is 4 to 8 times the diameter. The cable datasheet governs.

Next step

See your own range in 3D.

In 30 minutes we show how your installers configure, what arrives on your side and what the client version on your range involves.

Manufacturer or wholesaler

Book a demo with Ismail

You see the configurator in your own brand and we discuss your range, systems and markets.

Reply from Ismail within one working day

Installer

Configure for free

A trapeze, frame or tray with cables in a few minutes, with a bill of materials and drawing.

Enquiry goes to a supplier · reply within one working day