Cable tray supports decide whether a containment run stays level for twenty years or starts to sag after the second cable pull. The tray itself is rarely the problem. Trouble comes from a missing support at a bend, a coupler in the middle of a span or an anchor that was never checked for the load. This guide covers the support types, spacing, coupler positions and fixings in the order a site engineer or designer would work through them, with sizes and a worked example.
What are the six common types of cable tray support?
On UK sites the same six support types come up again and again. The grouping below is a practical one; no standard prescribes it.
| Support type | Typical use | Main parts |
|---|---|---|
| Trapeze bracket | Standard for trays from about 200 mm wide and for multi-tier runs | 2 drop rods, strut cross-member, channel nuts, washers, nuts, soffit fixing |
| Centre hanger | Light trays and narrow cable basket | 1 drop rod, centre hanger or omega support |
| Cantilever arm | Along walls and columns | Cantilever arm, wall fixing |
| Floor-standing H-frame | Plant rooms, roofs and floors | 2 uprights, cross-member, base plates |
| Christmas tree bracket | Arms on both sides of one upright | Upright, arms per tier, fittings |
| Stand-off bracket | Tray fixed direct to wall or soffit | Stand-off bracket, anchor |
Practical grouping from site experience, indicative.
One supplier limit as an example: an omega support for wire basket is rated for installation on a single central drop rod up to 300 mm wide [3]. Wider or heavier means a trapeze.
How far can you span a cable tray?
IEC 61537 (BS EN 61537 in the UK) sets out how manufacturers test the safe working load (SWL) of cable tray and cable ladder systems [1]. Every manufacturer therefore publishes an SWL at a stated span, and that is the figure to design to. For a first layout, these rules of thumb are a reasonable start:
| Containment | Support centres (rule of thumb) | Note |
|---|---|---|
| Sheet steel cable tray | 1.5 m, up to 2.0 m when lightly loaded | Light-duty tray is only 12 to 18 mm deep [4] |
| Cable basket | 1.5 m | Shorter for full 100 mm deep basket |
| Cable ladder | 3.0 m | Heavy-duty ladder is built for longer spans [5] |
| Fire-rated (circuit integrity) runs | As per the test report | Usually shorter than standard |
Rule of thumb, indicative. The manufacturer’s SWL per span governs.
Lengths match these centres: tray comes in 3 m lengths, ladder in 3 m and 6 m [4][5].
What is a trapeze type support?
A trapeze is a strut cross-member hung on two drop rods. The tray sits on top, held by hold-down clamps. Make the cross-member 150 to 200 mm wider than the tray so the studding, nuts and washers clear the tray edge (rule of thumb, indicative). For multi-tier runs, hang several cross-members on the same rods at about 300 mm centres (rule of thumb, indicative).
Where should couplers and extra supports go?
Three rules prevent most sagging runs:
- Couplers away from mid-span. Place a coupler about a quarter of the span from a support (rule of thumb, indicative). Bending moment peaks at mid-span.
- Support every fitting. Put a support within 0.5 m of each bend, tee, reducer and end (rule of thumb, indicative).
- Expansion couplers at movement joints. Where the route crosses a building movement joint, fit an expansion coupler. Ladder and tray ranges include them [5].
How do you work out the load on each support?
Take the self-weight of the containment, add the cables per metre and multiply by the support centres. On a trapeze, the load splits over two rods.
Worked example for a heavy power run on cable ladder:
| Item | Value | Source |
|---|---|---|
| Cable ladder 900 mm wide, 150 mm side rail | 9.66 kg/m | Manufacturer data [5] |
| 40 × 5-core 16 mm² at about 1.1 kg/m | 44.0 kg/m | Rule of thumb, indicative [8] |
| Total per metre | 53.7 kg/m | Calculated |
| Load per trapeze at 3.0 m centres | 161 kg, about 1.58 kN | Calculated |
| Load per drop rod | about 0.79 kN | Calculated |
| 41×41×2.5 mm slotted channel, 1,250 mm span | 3.21 kN max. UDL, 3.07 kN at L/200 | Manufacturer data [6] |
Loads are indicative; the manufacturer confirms.
The ladder is only 11% full by area, yet the weight is substantial. A single 41×41 channel still works at 1,250 mm, and a back-to-back channel gives more margin if you want to limit deflection. The bigger question is the drop rod and its anchor at about 0.8 kN each.
Which studding and fixings should you use?
The studding carries the load into the structure. Its strength depends on the tensile stress area from ISO 898-1: 36.6 mm² for M8, 58.0 mm² for M10 and 84.3 mm² for M12 [2]. With the property class (4.8 or 8.8) and a safety factor, that gives an indicative capacity. The full table by size is in threaded rod load table.
Fixings by substrate:
- Concrete soffit: an anchor approved for the substrate and the load. The anchor manufacturer states the permissible load.
- Steelwork: a beam clamp. Permissible working loads by type range from 1,000 to 4,550 N in one supplier’s range [7]. Choose by flange and load.
- Fire performance: BS 7671 regulation 521.10.202 requires wiring systems to be supported against premature collapse in a fire [9]. Use metal supports and fixings throughout.
Which finish suits the environment?
| Finish | Use | Data |
|---|---|---|
| Pre-galvanised | Indoors, dry areas | Standard for tray and channel |
| Hot-dip galvanised | Outdoors, damp, industrial | To BS EN ISO 1461; 45–55 µm on channel, 60–70 µm on ladder [5] |
| Stainless steel 316 | Coastal, chemical, pools | Available for ladder and tray [5] |
| Zinc-aluminium | Cable basket in damp areas | Offered on UK wire basket ranges [10] |
Manufacturer data; application indicative.
In the configurator you pick the environment first and it proposes a finish, which you can override. The trapeze, drop rods and soffit fixings come out together in one bill of materials.
Where do these figures come from?
- IEC 61537 (BS EN 61537), Cable management. Cable tray systems and cable ladder systems.
- ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel. Part 1: Bolts, screws and studs.
- Eurostrut, product page for omega support for wire basket: single central drop rod up to 300 mm wide. Accessed 19 November 2026. https://eurostrut.com/rejiband-omega-splus-draagprofiel-100mm-sv/63022104
- Atkore UK, cable tray product pages: light duty 12 and 18 mm deep, medium 25 mm, heavy 50 mm, extra heavy 100 mm, 3 m lengths. Accessed 19 November 2026. https://www.atkore.com/en-gb/products/cable-management-systems/TULL
- Eurostrut, ECL cable ladder product pages (900 × 150 mm at 9.66 kg/m, 6 m lengths, HDG 60–70 µm, IEC 61537, SS 316, expansion couplers) and strut channel (HDG 45–55 µm). Accessed 19 November 2026. https://eurostrut.com/kabeldraagsystemen/ecl-kabelladders/ · Atkore UK, cable ladder U10 to U15 (3 and 6 m, heavy duty for long spans). https://www.atkore.com/en-gb/products/cable-management-systems/U12
- Atkore UK, product page for 41×41×2.5 mm slotted channel, Beam Loading table. Accessed 19 November 2026. https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P1000T
- Eurostrut, beam clamp product pages, permissible working load by type. Accessed 19 November 2026. https://eurostrut.com/montage-systemen/klemmen/
- Cable weights: typical datasheet values (rule of thumb, indicative). The datasheet of the chosen cable governs.
- BS 7671, Requirements for Electrical Installations (IET Wiring Regulations), regulation 521.10.202.
- Atkore UK, steel wire cable tray product pages (finishes incl. zinc-aluminium). Accessed 19 November 2026. https://www.atkore.com/en-gb/products/cable-management-systems/MC55
Frequently asked questions
How far can you span a cable tray?
As a rule of thumb, 1.5 m for sheet steel tray and wire basket and 3 m for cable ladder (indicative). Heavy-duty ladder is designed for longer spans. Under IEC 61537 the manufacturer declares a safe working load at a stated span, and that figure governs.
What is a trapeze type support?
A trapeze is a horizontal cross-member, usually 41 mm strut channel, hung from two drop rods fixed to the soffit or steelwork. The tray sits on the cross-member. Several cross-members on the same rods give a multi-tier trapeze.
What size studding is used for cable tray?
M8 for light trays, M10 for most trapezes and M12 for heavy ladder runs is a common pattern. Choose by the load per rod and the manufacturer's data. The tensile stress area of M10 is 58.0 mm² according to ISO 898-1.
Do cable tray supports need to be metal?
In the UK, BS 7671 regulation 521.10.202 requires wiring systems to be supported so they will not collapse prematurely in a fire. In practice that means metal supports and fixings, with no reliance on plastic clips or ties alone.
https://strutconfigurator-site.pages.dev/en/knowledge-base/cable-tray-supports/ · Updated 19 November 2026 · Indicative; the manufacturer confirms.